联系我们
公司名称：XXX
电话：XXX
手机：XXX
联系人：XXX
地址：XXX
新闻动态
拉力机的数据提取和结束条件
拉力机测试数据的提取、删除和打印输出。显示及打印参数代号说明符号，代表的参量符号，代表的参量F抗张力 F。抗张力平均值S抗张强度φ 伸长率(相对伸长) 伸长量，抗张指数LB裂断长Z抗张能量汲取值W试样定量 IZ抗张能量汲取指数L夹间距(试验长度) 试样宽度。提取一组试验完毕，按查看键，可提取各个数值。删除 一次试验完毕后，按“删除”键，挑选您要删除的数据序号，按测试键确认。打印输出 一组试验完毕，按“打印”键，仪器自动打印全部数值。内存数据的清除，关断电源复新开机，系统复新进行初始化，清除全部内存数据。在待测试界面，按“清除”键，清除内存中的全部测试数据，按查看键确定数据是否全部清零。采纳以上方法清除内存数据，用户置入的试样定量、试验速度和夹间距均不会被清除。
Extraction, deletion and printing of test data of tractor. Display and print parameter symbol, parameter symbol, parameter F, tension resistance F. The average tensile strength of S is the elongation of_ (relative elongation), and the tensile index of LB is the elongation of Z. The tensile energy absorption value of W sample quantitatively implies the width of L-clip spacing of L-clip (test length). After extracting a group of experiments, each value can be extracted by pressing the viewing key. After deleting a test, press the "delete" key, select the serial number of the data you want to delete, and confirm by the test key. Print out a set of tests, press the "print" key, the instrument automatically prints all the values. Removal of memory data, power off and restart boot, system restore initialization, remove all memory data. In the interface to be tested, press the "Clear" key to clear all test data in memory, and press the "Check" key to determine whether all data is cleared. By adopting the above methods to clear the memory data, the sample quantity, test speed and clamp spacing inserted by users will not be cleared.
拉力机的结束条件，依据标准上试验过程的要求，如果要将试样破坏掉的（比如拉伸，水泥压缩）,挑选“破型推断”；如果拉（或压） 到某个试验力就结束的，挑选“目标”、“试验力”； 如果拉（或压）到某个变形就结束的，挑选“目标”、“变形”试验开始：点“试验开始”按钮开始试验。试验结束：试验完成后“试验结束”按钮自动按下。如果需要中途结束试验，也可以按下“试验结束”按钮手动结束试验。试验结果：点“分析”按钮查看相应的试验结果。继续试验，点“试验”按钮返回试验操作界面，点“下一个”按钮将是试验记录切换到下一条，复复5-11步进行试验。保存数据：如果试验数据需要保存，按“保存”按钮将试验 数据保存到数据库，以备查阅。打印报表：如果试验结果需要打印，按“输出报表”按钮将试验结果输出到 Word 文档并打印。关机：先关闭试验机电源，再关闭软件测控系统和电脑。
According to the requirement of the standard test process, if the specimen is destroyed (such as tension, cement compression), the "breakage inference" is selected; if the tension (or compression) ends at a certain test force, the "target" and "test force" are selected; if the tension (or compression) ends at a certain deformation, the "target" and "deformation" tests are selected to start. Start the test by clicking the "Test Start" button. End of the test: After the test is completed, the "End of the test" button is pressed automatically. If you need to end the test halfway, you can also press the "end of the test" button to manually end the test. Test results: Click the "Analysis" button to see the corresponding test results. Continue the test, click the "test" button to return to the test operation interface, click the "next" button to switch the test record to the next one, and repeat 5-11 steps for the test. Save data: If the test data need to be saved, press the "Save" button to save the test data to the database for reference. Print report: If the test results need to be printed, press the "Output Report" button to output the test results to the Word document and print. Shut down: First turn off the power supply of the test machine, then turn off the software measurement and control system and computer.
Extraction, deletion and printing of test data of tractor. Display and print parameter symbol, parameter symbol, parameter F, tension resistance F. The average tensile strength of S is the elongation of_ (relative elongation), and the tensile index of LB is the elongation of Z. The tensile energy absorption value of W sample quantitatively implies the width of L-clip spacing of L-clip (test length). After extracting a group of experiments, each value can be extracted by pressing the viewing key. After deleting a test, press the "delete" key, select the serial number of the data you want to delete, and confirm by the test key. Print out a set of tests, press the "print" key, the instrument automatically prints all the values. Removal of memory data, power off and restart boot, system restore initialization, remove all memory data. In the interface to be tested, press the "Clear" key to clear all test data in memory, and press the "Check" key to determine whether all data is cleared. By adopting the above methods to clear the memory data, the sample quantity, test speed and clamp spacing inserted by users will not be cleared.
拉力机的结束条件，依据标准上试验过程的要求，如果要将试样破坏掉的（比如拉伸，水泥压缩）,挑选“破型推断”；如果拉（或压） 到某个试验力就结束的，挑选“目标”、“试验力”； 如果拉（或压）到某个变形就结束的，挑选“目标”、“变形”试验开始：点“试验开始”按钮开始试验。试验结束：试验完成后“试验结束”按钮自动按下。如果需要中途结束试验，也可以按下“试验结束”按钮手动结束试验。试验结果：点“分析”按钮查看相应的试验结果。继续试验，点“试验”按钮返回试验操作界面，点“下一个”按钮将是试验记录切换到下一条，复复5-11步进行试验。保存数据：如果试验数据需要保存，按“保存”按钮将试验 数据保存到数据库，以备查阅。打印报表：如果试验结果需要打印，按“输出报表”按钮将试验结果输出到 Word 文档并打印。关机：先关闭试验机电源，再关闭软件测控系统和电脑。
According to the requirement of the standard test process, if the specimen is destroyed (such as tension, cement compression), the "breakage inference" is selected; if the tension (or compression) ends at a certain test force, the "target" and "test force" are selected; if the tension (or compression) ends at a certain deformation, the "target" and "deformation" tests are selected to start. Start the test by clicking the "Test Start" button. End of the test: After the test is completed, the "End of the test" button is pressed automatically. If you need to end the test halfway, you can also press the "end of the test" button to manually end the test. Test results: Click the "Analysis" button to see the corresponding test results. Continue the test, click the "test" button to return to the test operation interface, click the "next" button to switch the test record to the next one, and repeat 5-11 steps for the test. Save data: If the test data need to be saved, press the "Save" button to save the test data to the database for reference. Print report: If the test results need to be printed, press the "Output Report" button to output the test results to the Word document and print. Shut down: First turn off the power supply of the test machine, then turn off the software measurement and control system and computer.
